Browse Categories

pressure class

pressure class control valves hvac systems industrial valves

Industry Term of the week: Pressure Class

What “Pressure Class” Means


  • It’s a rating system (Class 125, 150, 250, 300, 600, 900, etc.) that defines how much pressure the valve can handle.

  • The rating is based on ASME/ANSI standards—most commonly ASME B16.34 and B16.5 for flanges.

  • Higher class = stronger, thicker valve body designed for higher pressures and temperatures.

(NOTE: specifically for Globe valves and ANSI 250)

  • The “Class 250” designation is a pressure class used primarily for flanges and valves made of gray cast iron.

How It Works


  • Each pressure class has an associated pressure-temperature table.
  • As fluid temperature increases, the allowable pressure decreases, even within the same class.
  • Example: A Class 150 valve might be rated for 285 psi at 100°F, But only 150 psi at 400°F.

Why It Matters


  • Ensures the valve body won’t burst or deform under system pressure.
  • Helps match the valve to the system’s piping pressure rating (e.g., if the system uses 150-lb piping, you typically use a Class 150 valve).
  • Avoids code violations in mechanical/HVAC systems.

Control Valve Specifics

Even though control valve sizing depends on Cv and actuator torque, the valve body still must match the system pressure class.

  1. Body pressure class = mechanical integrity
  2. Trim selection = control performance

Common HVAC examples:

  • 2-way and 3-way valves on chilled/hot water: Class 125 or 150
  • Steam control valves: Class 250, 300, or 600, depending on pressure

Rule of Thumb for choosing the right pressure class valve:


Choose a pressure class that:

  • Meets or exceeds system MAWP (maximum allowable working pressure)
  • Matches the piping flange class.

Some Common Selection tips:


  • If you see a valve specified as “Class 125 or 250” you’re probably looking for a flanged Globe valve 2.5in up to 6in.
  • Common Vendors: Belimo, Honeywell, Schneider Electric, Siemens, JCI
  • ANSI class will determine flange bolt pattern and is typically in most specs.
  • Don’t assume 8 bolt flanges are always ANSI 250, they may be for a higher rating as well.
  • You’ll want to verify the flange bolt pattern, valve material (cast iron vs ductile vs steel) and what temperature it will operate at if not provided in the specs
  • In HVAC hydronic systems: If you’re using cast iron valves in moderate pressure, moderate temperature service, a Class 125/250 body may be acceptable—but for higher temperature/pressure or critical service (steam or high-temp water) you’ll likely need a higher class or different material.
   Pressure Class

Tags

bas networking distech building automation iot ot control valves hvac systems industrial valves eclypse tosibox jci bas network hvac pumps hydronic systems commercial hvac centrifugal pumps chilled water systems heating water systems boiler safety boiler components industrial heating equipment heating systems chiller jace Pneumatic Electro-Mechanical and DDC systems maintenance calibration remote bacnet n4 automation honeywell control panels network configuration port security network control smart buildings energy management ethernet based bas network guidelines managed switches optimizer commander johnson controls pump selection pump sizing hydronic pump design pump fundamentals gpm flow rate total dynamic head tdh head pressure closed loop systems open loop systems glycol systems pump control strategies vfd pumps ecm pumps bas integration pump configuration inline pumps end suction pumps split case pumps redundant pumping lead lag pumps npsh hvac fundamentals industry terms pumps in hvac hydronic pump basics boiler systems hvac pump operation gpm and head pressure ahr boiler control Low Water Cut off Air Handler Unit AHU Air Handling Units HVAC Equipment york compressor tp valve temperature and pressure relief valve water heater safety domestic hot water systems plumbing safety devices pressure relief valves thermal expansion protection potable water systems water heater components mechanical code compliance plumbing code requirements boiler vs tp valve hot water storage tanks safety valves facility maintenance boiler relief valves dwyeromega ief electromagnetic flow transmitter optional lcd remote display AI future pressure class belimo gas monitor air quality training certification atrius cloud platform fireye burnlogix yb honeywell q tosi n5 bacnetsc sc niagara fx heating season checklist tc500 9000 8000 promo chart recorder industrial cxc customer center dcv sensor network security cyber ul508a industrial solutions engineering solutions panel assembly custom control panels commercial panels gas regulator sizing gas safety inlet pressure outlet pressure flow rate natural gas propane regulators subnet it managed ip switch vlan setup quality of service qos spanning tree protocol stp routing configuration network management lldp setup energy efficiency ethernet managed network switch benefits ot network energy savings building solutions connected power building management bms transformers din rail transformer functional devices transformer in a box ai in real estate cybersecurity data integration realcomm ibcon sustainability sensors controllers interfaces
Show All

Posts

2026 2025
December November October September August July June May April February January
2024
November October September August July June May April March February January
2023
December November October September August July June May April March
2022