Browse Categories

Beyond the Multimeter: Tools Every BAS Technician Should Have

Every BAS technician has the basics, but sometimes it’s the less-obvious tools that can save the most time on a jobsite. In this guide, we go beyond the multimeter and break down practical tools for troubleshooting BACnet and RS-485 networks, simulating inputs and outputs, verifying BAS values, testing IP networks, and isolating problems faster.

Why it matters: Whether you’re building your first BAS toolbox or looking for a few additions to your truck, these are the tools and troubleshooting kits worth having before you actually need them.


Beyond the Multimeter: Uncommon Tools Every Controls Technician Should Have | Stromquist & Company
BAS Technician Toolbox Guide

Beyond the Multimeter: Uncommon Tools Every Controls Technician Should Have

Every technician knows the basics: a good multimeter, screwdrivers, wire strippers, hand tools, and a laptop. But once you start commissioning and troubleshooting real building automation systems, another category of tools can make your life a whole lot easier.

The goal is not to carry the most tools. It is to have the right tool available to isolate the problem: sensor, wiring, controller, network, programming, or mechanical equipment.

Jump to a Section

Each section below can be opened and collapsed so you can quickly get to the tools you need.

What’s in Your BAS Toolbox?

We put together our list—but we know every System Integrator has a few go-to tools of their own. What did we miss? Share the tools, testers, adapters, or jobsite lifesavers you think belong on the list.

Networking & BACnet Tools

Modern controls technicians are part HVAC technician, part electrician, and increasingly, part network technician.

USB-to-RS485 Adapter

A USB-to-RS485 adapter allows a laptop to connect directly to an RS-485 network.

Depending on the software being used, it can be extremely useful when troubleshooting:

  • BACnet MS/TP
  • Modbus RTU
  • Device addressing
  • Communication problems
  • Individual field devices

It gives you another way to determine whether the controller, network, or BAS front end is causing the problem.

BACnet Discovery & Troubleshooting Software

An independent BACnet troubleshooting utility on your laptop can help determine whether devices are visible on the network without relying entirely on the BAS front end.

  • BACnet device discovery
  • Device IDs
  • IP addresses
  • BACnet objects
  • Duplicate device IDs
  • Communication issues
An independent tool gives you another perspective when the BAS is not showing what you expect.

A Second USB Ethernet Adapter

This may be one of the cheapest productivity upgrades for a BAS technician.

NIC #1 to Customer/BAS Network   |   NIC #2 to JACE, Controller, or Private Network

It can also make troubleshooting IP addresses, routing, DHCP, and subnet problems much easier.

Small Unmanaged Ethernet Switch

A small Ethernet switch can be extremely handy for creating a temporary network or connecting several devices during commissioning.

Laptop to Switch to JACE to IP Controller

It can also help isolate BAS equipment from the customer's larger network while troubleshooting.

Travel Router

A small travel router lets you create a temporary private network for commissioning or bench testing, especially before the customer's permanent network is available.

Ethernet Cable Tester

Do not spend an hour troubleshooting BACnet/IP when the problem is actually the cable.

  • Opens
  • Shorts
  • Miswired pairs
  • Damaged conductors

Add known-good patch cables, Ethernet couplers, an RJ45 crimper, and spare connectors for a simple network repair kit.

Build an “RS-485 Bag”

Consider making a small pouch labeled RS-485 standard equipment.

  • 120-ohm resistors
  • USB-to-RS485 adapter
  • Small screwdriver
  • Short pieces of shielded twisted-pair cable
  • Wire connectors or Wagos
  • Alligator jumpers
  • Spare terminal blocks
  • RS-485 troubleshooting cheat sheet

When a BACnet MS/TP or Modbus trunk goes sideways, everything you need is already in one place.

Do Not Forget the 120-Ohm Resistors

A couple of 120-ohm resistors take up almost no room in a toolbox, but can be invaluable when troubleshooting RS-485 communication problems and verifying proper end-of-line termination.

A perfect example of a very inexpensive item that can save a tremendous amount of time.
Back to Top
Tools for Simulating Inputs & Outputs

Some of the most useful BAS troubleshooting tools let you simulate what the controller should be seeing or sending. Instead of guessing, substitute a known signal and observe what happens.

Resistance Decade Box

A resistance decade box is one of the best troubleshooting tools many new BAS technicians have never used.

Imagine a controller has a 10K thermistor connected to an analog input, but the BAS is displaying 87°F when the space clearly is not 87°F.

Sensor to Wiring to Controller Input to Configuration to BAS Software

Disconnect the sensor and substitute a known resistance. If the controller now displays the expected temperature, you have eliminated a large portion of the system from suspicion.

A precision resistor kit can accomplish the same basic idea, but a decade box makes changing resistance values much easier.

0–10 V & 4–20 mA Signal Generators

Signal generators turn troubleshooting into a controlled experiment.

BAS to Controller to Analog Output to Wiring to VFD to Motor

Disconnect the controller's analog output and connect a 0–10 V signal generator directly to the VFD. Command 5 V and observe the response.

The same technique can be used with:

  • Control valves
  • Damper actuators
  • VFDs
  • Pressure sensors
  • Flow transmitters
  • Humidity transmitters
  • Industrial instrumentation
A good controls technician does not just ask, “Why isn't this working?” They ask, “What can I substitute or isolate to prove which part isn't working?”
Back to Top
Tools for Verifying What the BAS Is Telling You

Just because a value appears on the BAS does not mean it is correct. Independent measurements are critical.

Differential Pressure Manometer

If the BAS says duct static pressure is 1.7 inches w.c., how do you know that is actually true? Measure it.

  • Duct static pressure
  • Building pressure
  • Filter differential pressure
  • Airflow pressure relationships
  • Pressure sensor calibration

Sometimes the BAS is controlling perfectly based on bad information from a sensor.

Temperature Probe

Use an independent temperature probe to compare actual temperature against space sensors, discharge-air sensors, return-air sensors, outside-air sensors, pipe sensors, and BAS values.

Before changing programming because “the temperature is wrong,” verify that the temperature is actually wrong.

IR Thermometer

An infrared thermometer is not a replacement for a proper temperature probe, but it is a great quick diagnostic tool.

  • Hot-water pipes
  • Chilled-water pipes
  • Coils
  • Discharge-air temperatures
  • Equipment surfaces
Back to Top
Better Multimeter Accessories

Sometimes you do not need another meter. You just need better ways to use the one you already have.

Useful Add-Ons

  • Alligator-clip leads
  • Needle probes
  • Back-probe leads
  • Mini jumper leads
  • Low-current DC clamp capability

Alligator clips let you monitor a measurement without holding two probes in place. Back probes can let you measure a signal without disconnecting the circuit. Jumper leads can help temporarily simulate contacts, commons, and other signals during commissioning.

Back to Top
Create a “Known-Good” Box

One of the best troubleshooting kits a technician can build is not something you buy preassembled. It is a collection of known-good components.

What to Keep Inside

  • 10K temperature sensor
  • 0–10 V device
  • 4–20 mA device
  • Relay
  • BACnet MS/TP device
  • BACnet/IP device
  • 24 VAC transformer
  • 24 VDC power supply
  • Known-good Ethernet cable

Troubleshooting frequently comes down to substitution and isolation. Every successful substitution reduces the number of possible causes.

Back to Top
The “Why Didn’t I Bring That?” Tools

Not everything needs to be technical. Some of the most appreciated tools in a BAS technician's truck are the ones that solve annoying jobsite problems.

Magnetic extension wand: Because eventually you are going to drop a panel screw somewhere it should not be.
Inspection mirror: Useful for reading labels, LEDs, model numbers, and wiring hidden behind equipment.
USB borescope: Even better when equipment is above ceilings or installed where no human was intended to reach.
Headlamp: Keeps both hands available for actual work.
Magnetic parts tray: Keeps screws and small components from disappearing while working inside a panel.
Label maker: A troubleshooting repair should ideally leave the system easier for the next technician to understand.
Fine-tip permanent markers: Mark wires before disconnecting them. Your future self will appreciate it.
Back to Top
Carry a Small BAS “Get Me Out of Trouble” Kit

Every technician eventually develops a collection of parts that have saved a job. A new technician can get ahead of that process.

Useful Spares

  • Fuses
  • Terminal jumpers
  • Wire connectors
  • Short pieces of control wire
  • 120-ohm resistors
  • Spare terminal blocks
  • Ethernet couplers
  • Short patch cables
  • Small 24 VAC transformer
  • 24 VDC power supply
  • Test leads
  • Common resistors
You are not trying to carry an entire warehouse. You are carrying enough material to test a theory, temporarily substitute a component, or finish troubleshooting.
Back to Top
The Cheapest Tool on the List: A BAS Field Notebook

One of the most useful tools might cost less than $10. Carry a dedicated BAS field notebook—and turn the back section into your personal troubleshooting reference.

Electrical: Ohm's Law, power formulas, VA calculations, 0–10 V conversions, 4–20 mA conversions.
Sensors: Common 10K thermistors, 10K Type II/III curves, PT100, PT1000, and other regularly encountered sensors.
BACnet MS/TP: MAC addressing, baud rates, polarity conventions, termination, biasing basics, and common troubleshooting procedures.
IP Networking: Common subnet masks, private IP ranges, default gateway basics, BACnet/IP ports, ping, arp, ipconfig, and tracert.
Niagara: Common ports, platform vs. station connections, IP changeover procedures, commissioning checklists, and frequently used troubleshooting procedures.
Every time you learn something useful in the field, add it. After a few years, that notebook becomes something you cannot buy: your own BAS field troubleshooting manual.
Back to Top
Don’t Build a Toolbox. Build Troubleshooting Kits.

When outfitting a new BAS technician, handing them a list of 50 tools is not necessarily the best approach. Organize the truck around five troubleshooting kits instead.

1. Electrical & I/O: Meters, probes, resistors, signal generators, transformers, power supplies, and jumpers.
2. BACnet & RS-485: USB-to-RS485 adapter, terminating resistors, cable, connectors, and reference information.
3. IP Networking: Ethernet adapters, switch, travel router, patch cables, couplers, tester, and network software.
4. HVAC Verification: Temperature probes, manometer, IR thermometer, and other independent measurement tools.
5. “Get Me Out of Trouble” Spares: Fuses, connectors, terminal blocks, jumpers, patch cables, resistors, and known-good devices.
The point is not just to know which tools to buy. It is to learn how to approach a problem: break the system into pieces, measure it, simulate it, substitute something known-good, and eliminate possibilities one at a time.
Back to Top
The Bottom Line

The Best BAS Technicians Know What to Test Next

The best BAS technicians are not necessarily the people carrying the most tools. They are the technicians who know which tool to grab next—and what that test will prove.

What’s in Your BAS Toolbox?

Think we missed something? We want to hear from the System Integrators and controls technicians doing this work every day. Share the tools you would add to the list.

Tags

bas icg distech honeywell iot networking building automation tosi jace eclypse control valves ot bacnet niagara remote pressure optimizer hvac systems industrial valves tosibox jci bas network boiler combustion tridium hvac controls fx future penn temperature flow york belimo fuel train control 8000 9000 dwyeromega remote display hvac pumps hydronic systems commercial hvac centrifugal pumps chilled water systems heating water systems boiler safety boiler components industrial heating equipment heating systems chiller Pneumatic Electro-Mechanical and DDC systems maintenance calibration n4 automation control panels network configuration port security network control smart buildings energy management ethernet based bas network guidelines managed switches commander johnson controls eol lumen radio wireless mesh system installation communication devices fault bog troubleshoot resense air resense move 75 stromquist wallpaper jace 9000 tec firmware building automation systems controls technician bas technician engineering kit toolbox tools maxon ssov name plate modbus lumenradio wireless software loytec t4031a t775 temp controller ecy distech controls honeywell webs saas service subscription connect resense tin 550 system 550 a2l easyio end of life EOL level humidity ph conductivity modular multistage controller graphics controls universal digital controller plug valve manual ball ball hvac contactors starters soft starters vfds sight glass peerless penumatic pe ep switch data center hvac modern metering requirements rma warranty thermal blower wheel impeller fan wheel air handler receiver controllers velocity controlle reset volume controllers rs transmitter transducer link config IAQ Indoor Air Quality IAQ sensors Filtration Ventilation bypass valve hydrolic system mixing valve diverting valve KMC Control lines Conquest Commander KMC software solutions engineer panel Lead/Lag HVAC pumps boilers chillers RTUs globe valves hvac valves pneumatic thermostats calibrating pneumatic thermostats how pneumatic thermostats work tosi control sma device count points Gas Meters Diaphragm Rotary meters gas trains gas supply commercial boiler burner ief transmitters Gas Valves for boilers Vent Valves Pilot Gas Valves switches for boilers a temperature sensor honeywell i4006 honeywell l6006c honeywell l91b temperature limit switches gas pressure limit switches pump selection pump sizing hydronic pump design pump fundamentals gpm flow rate total dynamic head tdh head pressure closed loop systems open loop systems glycol systems pump control strategies vfd pumps ecm pumps bas integration pump configuration inline pumps end suction pumps split case pumps redundant pumping lead lag pumps npsh hvac fundamentals industry terms pumps in hvac hydronic pump basics boiler systems hvac pump operation gpm and head pressure ahr Low Water Cut off Air Handler Unit AHU Air Handling Units HVAC Equipment compressor tp valve temperature and pressure relief valve water heater safety domestic hot water systems plumbing safety devices pressure relief valves thermal expansion protection potable water systems water heater components mechanical code compliance plumbing code requirements boiler vs tp valve hot water storage tanks safety valves facility maintenance boiler relief valves ief electromagnetic flow transmitter optional lcd AI pressure class gas monitor air quality training certification atrius cloud platform fireye burnlogix yb honeywell q n5 bacnetsc sc heating season checklist tc500 promo chart recorder industrial cxc customer center dcv sensor network security cyber ul508a industrial solutions engineering solutions panel assembly custom control panels commercial panels gas regulator sizing gas safety inlet pressure outlet pressure flow rate natural gas propane regulators subnet it managed ip switch vlan setup quality of service qos spanning tree protocol stp routing configuration network management lldp setup energy efficiency ethernet managed network switch benefits ot network energy savings building solutions connected power building management bms transformers din rail transformer functional devices transformer in a box ai in real estate cybersecurity data integration realcomm ibcon sustainability sensors controllers interfaces
Show All

Posts

2026
November October September August July June May April March February January
2025
December November October September August July June May April February January
2024
November October September August July June May April March February January
2023
December November October September August July June May April March
2022